Solid ash twin line diamond cabinet pull in the Unfinished finish, fitted across two doors

Twin Line Diamond Cabinet Pull, Solid Ash — Set of 2

Size 1: 92 mm / 32 mm / Unfinished
£21.00
Skip to product information
Solid ash twin line diamond cabinet pull in the Unfinished finish, fitted across two doors
1/5
  • Solid ash twin line diamond cabinet pull in the Unfinished finish, fitted across two doors
  • Twin line diamond cabinet pull in solid ash on a pale cabinet, lit from the side to show both grooves
  • Dimensioned drawings of the four twin line diamond pull sizes: 92, 122, 152 and 192 mm long, with 32, 64, 96 and 128 mm between centres
  • Twin line diamond cabinet pull in solid ash fitted across two doors, both grooves closing across the join
  • Half-diamond ash pulls with two carved lines, loose on a grey background with the mounting screws
Twin Line Diamond Cabinet Pull, Solid Ash — Set of 2

Twin Line Diamond Cabinet Pull, Solid Ash — Set of 2

£21.00

A diamond pull cut in two down the middle, with two grooves running one inside the other. Sold as a set of two halves in solid ash. Fitted either side of the gap between two doors, both lines close across the join and the diamond completes itself twice over.

The outer line follows the edge; the inner one repeats it a few millimetres in, with the corners rounded so the pair reads as a track rather than as a border. At an angle the two grooves catch the light at different moments, which is what gives the face depth on a shape that is otherwise flat.

Four sizes, from a 92 mm diamond on a bathroom cabinet to a 192 mm one on a wardrobe, and twelve finishes. The price changes with size only, not with finish.

Same shape, same four sizes, a different face: plain, with no carving, a single grooved outline, a carved leaf, mirrored arches or an interlaced weave.
Product details

A diamond cabinet pull in solid ash with two concentric grooves, split into two halves. Sold as a set of two, in four sizes and twelve finishes.

In the box: two half-diamond pulls with the threaded metal inserts already fitted, and four M4 × 30 mm screws — two per half.
Dimensions and specifications
  • Wood: solid ash, cut from a single block, no glued joints
  • Size 1: 80 × 92 mm (3.1″ × 3.6″), 32 mm between centres
  • Size 2: 110 × 122 mm (4.3″ × 4.8″), 64 mm between centres
  • Size 3: 140 × 152 mm (5.5″ × 6″), 96 mm between centres
  • Size 4: 180 × 192 mm (7.1″ × 7.6″), 128 mm between centres
  • Total depth from the door: 22 mm (0.9″), all sizes
  • Tolerance: ±1 mm
  • Mounting holes required: 4 mm, two per half
  • Fits door and drawer fronts up to 24 mm thick
  • Included: two half-diamond pulls and four M4 × 30 mm screws, two per half
  • Finish: ADLER Legno Dura-Öl, an oil-based finish — ten colours plus Oiled. Unfinished is bare sanded ash, with no coating at all
  • Sold as a set of two halves; price varies by size only
Mounting

Decide first which way the split will run: vertically, between two side-by-side doors, or horizontally, between two fronts stacked one above the other. The steps are the same either way — the pairs of holes simply run along the split rather than across it.

  1. On each front, mark two points at the centre distance for your size — 32, 64, 96 or 128 mm — running parallel to the split.
  2. Drill a 4 mm hole at each of the four points, through the front.
  3. Pass an M4 × 30 mm screw through each hole from the back and thread it into the insert in the half, tightening by hand with the straight edge along the split.
  4. Finish each screw with a quarter turn of a screwdriver — no more. Overtightening pulls the insert out of the wood.

Two lines cross the split instead of one, so a misalignment shows up twice over. Measure both fronts from the same reference edge rather than from each other, close them, and check both grooves before the screws grip. If your front is thinner than 24 mm, the screws will stand proud inside the inserts; that is normal and does not affect how the pull holds.
Materials & workshop

Wood: solid ash, single block per half. Hardware: two threaded metal inserts and two M4 × 30 mm screws per half.

Eleven of the twelve finishes use ADLER Legno Dura-Öl, an Austrian oil-based finish. It leaves a matt, open-pored surface — the colour sits in the wood rather than on top of it, so a green pull still reads as ash and not as painted board — while resisting water and household chemicals the way a varnish would. The oil is certified to EN 71-3 for the migration of heavy metals, and to DIN 53160-1 and 53160-2 for saliva and perspiration resistance. The twelfth option, Unfinished, is bare sanded ash with no coating; it is the palest of the set and darkens with handling.

Cut, shaped, sanded and finished in our own workshop in Roman, Romania. The two grooves have to stay exactly parallel over the whole run, which is the reason this pattern takes longer than a single line: any drift between them is obvious because the eye has something to compare against. Both are cut before the face is sanded, and the corners are cleaned up by hand so the rounded turns stay even.
Care

Wipe with a dry or barely damp cloth. The oil finish resists water and household cleaners, so no special product is needed and none is recommended.

Two grooves hold twice the dust of one; a dry brush run along them clears both in a single pass. Unfinished pulls have no coating and darken with handling.

You may also like