Solid ash diamond cabinet pull in the Unfinished finish, fitted across two doors

Diamond Cabinet Pull, Solid Ash — Set of 2

Size 1: 92 mm / 32 mm / Unfinished
£21.00
Skip to product information
Solid ash diamond cabinet pull in the Unfinished finish, fitted across two doors
1/5
  • Solid ash diamond cabinet pull in the Unfinished finish, fitted across two doors
  • Diamond cabinet pull in solid ash on a dark cabinet, lit from the side to show the plain face
  • Dimensioned drawings of the four diamond pull sizes: 92, 122, 152 and 192 mm long, with 32, 64, 96 and 128 mm between centres
  • Diamond cabinet pull in solid ash fitted across two white doors, seen at an angle
  • Half-diamond ash pulls loose on a grey background with the mounting screws
Diamond Cabinet Pull, Solid Ash — Set of 2

Diamond Cabinet Pull, Solid Ash — Set of 2

£21.00

A diamond pull cut in two down the middle, sold as a set of two halves in solid ash. Fitted either side of the gap between two doors, the halves close up into a single diamond; the wood is left plain, with no carving on it at all.

This is the shape without the pattern. Nothing on the face competes with the grain, and because ash runs in long straight lines the two halves — cut from the same board — read as one piece with a seam down it.

Four sizes, from a 92 mm diamond on a bathroom cabinet to a 192 mm one on a wardrobe, and twelve finishes. The price changes with size only, not with finish.

Same shape, same four sizes, a different face: a single grooved outline, two parallel lines, a carved leaf, mirrored arches or an interlaced weave.
Product details

A diamond cabinet pull in solid ash, split into two plain halves with no carving. Sold as a set of two, in four sizes and twelve finishes.

In the box: two half-diamond pulls with the threaded metal inserts already fitted, and four M4 × 30 mm screws — two per half.
Dimensions and specifications
  • Wood: solid ash, cut from a single block, no glued joints
  • Size 1: 80 × 92 mm (3.1″ × 3.6″), 32 mm between centres
  • Size 2: 110 × 122 mm (4.3″ × 4.8″), 64 mm between centres
  • Size 3: 140 × 152 mm (5.5″ × 6″), 96 mm between centres
  • Size 4: 180 × 192 mm (7.1″ × 7.6″), 128 mm between centres
  • Total depth from the door: 22 mm (0.9″), all sizes
  • Tolerance: ±1 mm
  • Mounting holes required: 4 mm, two per half
  • Fits door and drawer fronts up to 24 mm thick
  • Included: two half-diamond pulls and four M4 × 30 mm screws, two per half
  • Finish: ADLER Legno Dura-Öl, an oil-based finish — ten colours plus Oiled. Unfinished is bare sanded ash, with no coating at all
  • Sold as a set of two halves; price varies by size only
Mounting

Decide first which way the split will run: vertically, between two side-by-side doors, or horizontally, between two fronts stacked one above the other. The steps are the same either way — the pairs of holes simply run along the split rather than across it.

  1. On each front, mark two points at the centre distance for your size — 32, 64, 96 or 128 mm — running parallel to the split.
  2. Drill a 4 mm hole at each of the four points, through the front.
  3. Pass an M4 × 30 mm screw through each hole from the back and thread it into the insert in the half, tightening by hand with the straight edge along the split.
  4. Finish each screw with a quarter turn of a screwdriver — no more. Overtightening pulls the insert out of the wood.

A diamond meets in two points, top and bottom, and those points show any misalignment immediately — more than a circle would. Measure both fronts from the same reference edge rather than from each other, close them, and check before the screws grip. If your front is thinner than 24 mm, the screws will stand proud inside the inserts; that is normal and does not affect how the pull holds.
Materials & workshop

Wood: solid ash, single block per half. Hardware: two threaded metal inserts and two M4 × 30 mm screws per half.

Eleven of the twelve finishes use ADLER Legno Dura-Öl, an Austrian oil-based finish. It leaves a matt, open-pored surface — the colour sits in the wood rather than on top of it, so a green pull still reads as ash and not as painted board — while resisting water and household chemicals the way a varnish would. The oil is certified to EN 71-3 for the migration of heavy metals, and to DIN 53160-1 and 53160-2 for saliva and perspiration resistance. The twelfth option, Unfinished, is bare sanded ash with no coating; it is the palest of the set and darkens with handling.

Cut, shaped, sanded and finished in our own workshop in Roman, Romania. With nothing carved into the face, this is the version where the wood has to be right: the two halves of a set are cut from the same board, next to each other, and stay together through finishing so the grain runs on across the join. On the largest size that is a 192 mm line of ash with no interruption — which is also why we do not sell the halves singly.
Care

Wipe with a dry or barely damp cloth. The oil finish resists water and household cleaners, so no special product is needed and none is recommended.

There is nothing carved into this one, so nothing traps dust. On Unfinished pulls the straight inner edge is where the hand lands and where the wood darkens first; oil them yourself before fitting if you would rather it did not.

You may also like