Solid ash framed diamond cabinet pull in the Unfinished finish, fitted across two doors

Framed Diamond Cabinet Pull, Solid Ash — Set of 2

Size 1: 92 mm / 32 mm / Unfinished
£21.00
Skip to product information
Solid ash framed diamond cabinet pull in the Unfinished finish, fitted across two doors
1/5
  • Solid ash framed diamond cabinet pull in the Unfinished finish, fitted across two doors
  • Framed diamond cabinet pull in solid ash on a pale cabinet, lit from the side to show the grooved outline
  • Dimensioned drawings of the four framed diamond pull sizes: 92, 122, 152 and 192 mm long, with 32, 64, 96 and 128 mm between centres
  • Framed diamond cabinet pull in solid ash fitted across two doors, the groove closing across the join
  • Half-diamond ash pulls with the grooved outline, loose on a grey background with the mounting screws
Framed Diamond Cabinet Pull, Solid Ash — Set of 2

Framed Diamond Cabinet Pull, Solid Ash — Set of 2

£21.00

A diamond pull cut in two down the middle, with a single groove following the outline. Sold as a set of two halves in solid ash. Fitted either side of the gap between two doors, the halves close up and the groove closes with them into one continuous diamond.

The line sits a few millimetres inside the edge and runs the whole way round, including through both points. It is the least decoration you can put on a shape and still change it: from across the room it reads as a drawn outline rather than a carved pattern, and it holds a shadow that follows the light through the day.

Four sizes, from a 92 mm diamond on a bathroom cabinet to a 192 mm one on a wardrobe, and twelve finishes. The price changes with size only, not with finish.

Same shape, same four sizes, a different face: plain, with no carving, two parallel lines, a carved leaf, mirrored arches or an interlaced weave.
Product details

A diamond cabinet pull in solid ash with a groove following the outline, split into two halves. Sold as a set of two, in four sizes and twelve finishes.

In the box: two half-diamond pulls with the threaded metal inserts already fitted, and four M4 × 30 mm screws — two per half.
Dimensions and specifications
  • Wood: solid ash, cut from a single block, no glued joints
  • Size 1: 80 × 92 mm (3.1″ × 3.6″), 32 mm between centres
  • Size 2: 110 × 122 mm (4.3″ × 4.8″), 64 mm between centres
  • Size 3: 140 × 152 mm (5.5″ × 6″), 96 mm between centres
  • Size 4: 180 × 192 mm (7.1″ × 7.6″), 128 mm between centres
  • Total depth from the door: 22 mm (0.9″), all sizes
  • Tolerance: ±1 mm
  • Mounting holes required: 4 mm, two per half
  • Fits door and drawer fronts up to 24 mm thick
  • Included: two half-diamond pulls and four M4 × 30 mm screws, two per half
  • Finish: ADLER Legno Dura-Öl, an oil-based finish — ten colours plus Oiled. Unfinished is bare sanded ash, with no coating at all
  • Sold as a set of two halves; price varies by size only
Mounting

Decide first which way the split will run: vertically, between two side-by-side doors, or horizontally, between two fronts stacked one above the other. The steps are the same either way — the pairs of holes simply run along the split rather than across it.

  1. On each front, mark two points at the centre distance for your size — 32, 64, 96 or 128 mm — running parallel to the split.
  2. Drill a 4 mm hole at each of the four points, through the front.
  3. Pass an M4 × 30 mm screw through each hole from the back and thread it into the insert in the half, tightening by hand with the straight edge along the split.
  4. Finish each screw with a quarter turn of a screwdriver — no more. Overtightening pulls the insert out of the wood.

The groove crosses the split at the top and the bottom, which makes alignment easy to judge and impossible to fake: if the two halves sit at different heights, the line steps at the join. Measure both fronts from the same reference edge, close them, and check before the screws grip. If your front is thinner than 24 mm, the screws will stand proud inside the inserts; that is normal and does not affect how the pull holds.
Materials & workshop

Wood: solid ash, single block per half. Hardware: two threaded metal inserts and two M4 × 30 mm screws per half.

Eleven of the twelve finishes use ADLER Legno Dura-Öl, an Austrian oil-based finish. It leaves a matt, open-pored surface — the colour sits in the wood rather than on top of it, so a green pull still reads as ash and not as painted board — while resisting water and household chemicals the way a varnish would. The oil is certified to EN 71-3 for the migration of heavy metals, and to DIN 53160-1 and 53160-2 for saliva and perspiration resistance. The twelfth option, Unfinished, is bare sanded ash with no coating; it is the palest of the set and darkens with handling.

Cut, shaped, sanded and finished in our own workshop in Roman, Romania. One line is harder than several: it has to keep the same distance from the edge the whole way round, and the two ends have to meet the split at exactly the same height on both halves or the diamond does not close. The groove is cut first and the face sanded afterwards along the line, never across it. It holds more oil than the flat, so on the coloured finishes it draws itself a shade darker.
Care

Wipe with a dry or barely damp cloth. The oil finish resists water and household cleaners, so no special product is needed and none is recommended.

The groove is shallow enough that a cloth reaches most of it; a dry brush clears the two points, where dust settles first. Unfinished pulls have no coating and darken with handling.

You may also like