Cloud-shaped ash cabinet knob, unfinished — bare sanded wood, palest of the range

Cloud Cabinet Knob, Solid Ash

Unfinished
£5.00
Skip to product information
Cloud-shaped ash cabinet knob, unfinished — bare sanded wood, palest of the range
1/8
  • Cloud-shaped ash cabinet knob, unfinished — bare sanded wood, palest of the range
  • Cloud Cabinet Knob, Solid Ash
  • Cloud-shaped ash cabinet knob in Blue, seen at an angle
  • Two cloud-shaped ash cabinet knobs with their mounting screws, one shown from the back with the threaded metal insert visible in the base
  • Two cloud-shaped ash cabinet knobs with their mounting screws, one in bare wood and one in Blue
  • Technical drawing of the cloud knob: 60 mm wide, 40 mm tall, 22 mm deep, 13 mm base
  • Cloud-shaped ash cabinet knob in bare wood, seen face on
  • Cloud-shaped ash cabinet knob in bare wood, seen at an angle
Cloud Cabinet Knob, Solid Ash

Cloud Cabinet Knob, Solid Ash

£5.00

A cloud-shaped cabinet knob, 60 mm wide, cut from a single block of solid ash. Sold individually, in twelve finishes.

Wider than it is tall, so it sits on a drawer front the way a handle does rather than a knob — you can hook two fingers over one of the lobes instead of pinching. That makes it easier for small hands, which is why it usually ends up on a child's wardrobe, but in one of the darker finishes the shape is quiet enough for a kitchen island.
Product details

A cloud-shaped cabinet knob in solid ash, 60 mm wide. Sold individually, in twelve finishes.

In the box: one knob with the threaded metal insert already fitted, and one M4 × 30 mm screw.
Dimensions and specifications
  • Wood: solid ash, cut from a single block, no glued joints
  • Face: 60 × 40 mm (2.4″ × 1.6″)
  • Total depth from the door: 22 mm (0.9″)
  • Base: 13 mm
  • Tolerance: ±1 mm
  • Mounting hole required: 4 mm
  • Fits door and drawer fronts up to 24 mm thick
  • Included: one M4 × 30 mm screw, threaded metal insert fitted in the knob
  • Weight: 30–40 g, depending on the piece of ash
  • Finish: ADLER Legno Dura-Öl, an oil-based finish — ten colours plus Oiled. Unfinished is bare sanded ash, with no coating at all
  • Sold individually
Mounting
  1. Check that your door already has a mounting hole. If not, drill a 4 mm hole through the front.
  2. Pass the M4 × 30 mm screw through the hole from the back of the door.
  3. Thread the screw into the metal insert in the knob and tighten by hand, holding the knob level.
  4. Finish with a quarter turn of a screwdriver — no more. Overtightening pulls the insert out of the wood.

The knob is 60 mm wide, so on a narrow drawer check the clearance to the edge before you drill. If your door is thinner than 24 mm, the screw will stand proud inside the insert; that is normal and does not affect how the knob holds.
Materials & workshop

Wood: solid ash, single block. Hardware: threaded metal insert and M4 × 30 mm screw.

Eleven of the twelve finishes use ADLER Legno Dura-Öl, an Austrian oil-based finish. It leaves a matt, open-pored surface — the colour sits in the wood rather than on top of it, so a green knob still reads as ash and not as painted board — while resisting water and household chemicals the way a varnish would. The oil is certified to EN 71-3 for the migration of heavy metals, and to DIN 53160-1 and 53160-2 for saliva and perspiration resistance. The twelfth option, Unfinished, is bare sanded ash with no coating; it is the palest of the set and darkens with handling.

Cut, shaped, sanded and finished in our own workshop in Roman, Romania. The three lobes are cut in one pass and rounded by hand, so the edge stays soft to the touch — there is no sharp corner anywhere on the knob. Colour and figure vary from piece to piece; if you are fitting a whole room, order them together and we will cut them from the same board where we can.
Care

Wipe with a dry or barely damp cloth. The oil finish resists water and household cleaners, so no special product is needed and none is recommended.

Unfinished knobs have no coating. They will pick up the marks of daily use and slowly darken. If you would rather they did not, oil them yourself before fitting.

You may also like